Compare Prices

Bipolar Stepper Motor Controller

Controller Stepper Bipolar Motor - TB6600 4A 9-42V Stepper Motor Driver CNC Controller with Stepper Motor Nema 17 Bipolar 1.7A 40N.cm Holding Torque and Motor Mounting Bracket for 3D Printer Hobby CNC Router XYZ by Beauty Star
TB6600 4A 9-42V Stepper Motor Driver CNC Controller with Stepper Motor Nema 17 Bipolar 1.7A 40N.cm Holding Torque and Motor Mounting Bracket for 3D Printer Hobby CNC Router XYZ by Beauty Star

(1) TB6600 Stepper Motor Driver: Single chip bipolar sine microstep stepper motor driver. New BiCD 0.13 nm process. Up to 42V. 5 subdivision mode options (1/1, 1/2, 1/4, 1/8, 1/16,1/32). Output current: IOUT = 4.0A (peak, in 100ms). rated output: IOUT = 3.5 A Resistance (a +) = 0.4 Alarm output pin current:Ialert = 1mA Monitoring output pin (MO): Imo= 1mA Break through the traditional, single power supply. Built in overheating protection (TSD) circuit. Undervoltage protection, built-in (UVLO) circuit. Built-in overcurrent detection (ISD), circuit. Can control 2 phase stepper motor forward and reverse rotation, With 1-2, W1 -2 , 2W1 -2, 4W1 -2 phase excitation mode. (2) Nema 17 Stepper Motor: Motor type: Bipolar Stepper Phase Resistance: 1.5Ohm Phase Inductance: 2.8mH Detent Torque: 2.2N.cm Rotor Inertia: 54g.cm2 Holding Torque: 40N.cm Step angle: 1.8 deg Motor Weight: 280g Step angle accuracy: + - 5%(full step, not load) Resistance accuracy: + - 10% Inductance accuracy: + - 20% Temperature rise: 80deg Max(rated current, 2 phase on) Ambient temperature: -20deg ~+50deg Insulation resistance: 100MΩ Min, 500VDC Insultion Strength: 500VAC for one minute Connection: Red(A+), Green(A-), Yellow(B+), Blue(B-) Package Included: 1 x TB6600 Motor Driver 1 x Nema 17 Motor 1 x Mounting Bra...

  • Brand: Beauty Star
  • ASIN: B075WTSGK6
  • UPC: 661273114728
  • Part No: 202425-US1
Motor Bipolar Stepper Controller - STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A 59Ncm(84oz.in) 48mm Body 4-lead W/ 1m Cable and Connector compatible with 3D Printer/CNC
STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A 59Ncm(84oz.in) 48mm Body 4-lead W/ 1m Cable and Connector compatible with 3D Printer/CNC

This is an updated version nema 17 stepper motor with holding torque of 59Ncm(83.6oz.in). Based on old verstion, we have lengthened motor cable length to 1 metre, and add a 4-pin 0.1" pitch (2.54mm) Harwin female connector at the end of cable. It's good ideal for 3D printers, as well as CNC and robotics applications. Important notice: Some customers reported they bought this model from other seller under this listing, but found much of difference with our description(no connector and shorter leads). We highly recommend you report this problem to Amazon if you have same experience. If you are a new buyer, please pay attention to our ID is "STEPPERONLINE", and our P/N is "17HS19-2004S1". Electrical Specification: * Manufacturer Part Number: 17HS19-2004S1 * Motor Type: Bipolar Stepper* Step Angle: 1.8 deg. * Holding Torque: 59Ncm(83.6oz.in)* Rated Current/phase: 2.0A* Phase Resistance: 1.4ohms* Inductance: 3.0mH+/-20%(1KHz) Physical Specification: * Frame Size: 42 x 42mm * Body Length: 48mm * Shaft Diameter: 5mm * Shaft Length: 24mm * D-cut Length: 15mm * Number of Leads: 4 * Lead Length: 1m with connector * Weight: 390g Connection: Black(A+), Green(A-), Red(B+), Blue(B-) Warning: Make sure the motor connect to a constant current or chopper drive controller before you test motor...

  • Color: As Shown
  • Brand: STEPPERONLINE
  • ASIN: B00PNEQKC0
  • UPC: 191388825313
  • Part No: 17HS19-2004S1
Controller Motor Stepper Bipolar - Stepper Motor Driver, MYSWEETY TB6600 0.2-5A Nema 17/23 CNC Controller Stepper Motor Driver 1 Axis 2 Phase Hybrid Stepper Motor
Stepper Motor Driver, MYSWEETY TB6600 0.2-5A Nema 17/23 CNC Controller Stepper Motor Driver 1 Axis 2 Phase Hybrid Stepper Motor

Feature: Equipped with the 3rd generation of breakout board, display panel and control pad to control the motor manually. Overload, overcurrent, overheat, overvoltage and undervoltage protection to avoid damaging your computer and devices. Cooling Aluminium Box Design for Cooling, and protect the driver board from being damaged by dirt, dust or other liquids. The TB1H is a high performance microstepping driver based on the latest original for TOSHIBA high-efficiency TB6600HG for IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Moreover, the brand new design with BiCD0.13 (50V) process technology on the chipset also ensures maximum 5.0A output current and 50V output withstand voltage. Specifics: Automatic idle-current reduction Supply voltage up to 50V DC Output current up to 5.0A High speed optoelectronic isolation signal input. Single-chip PWM bipolar sinusoidal chopper ensures low vibration and high efficiency. 1, 2, 4 (New Mode), 8, 16 adjustable microstep control, motors run more precisely and smoothly. Application: as long as the current range of the stepper motor is within 0.2-5 amps, all the 2 Phase or 4 Phase of Nema17, Nema23, Nema24 and Nema34 stepper motors will work perfectly with this new-type TB6600H...

  • Brand: MYSWEETY
  • ASIN: B07DJ9RGRD
  • UPC: 687345902697
  • Part No: 302018-new
Bipolar Stepper Controller Motor - Dual Bipolar Stepper Motor Shield For Arduino (DRV8825) Arduino Master Controller Easy To Drive Step Motor A Two Step Motor Can Be Connected To The Motor
Dual Bipolar Stepper Motor Shield For Arduino (DRV8825) Arduino Master Controller Easy To Drive Step Motor A Two Step Motor Can Be Connected To The Motor

INTRODUCTION Do you want to do some projects with stepper motors such as a drafting instrument, a 3D printer, an auto curtain......? As we all know, regular stepper motors are hard to drive, but with this stepper motor shield, you can easily drive 2 stepper motors via just 6 digital I/O pins.  Version Upgrade: 1.V2 replaces DRV8825 as stepper motor driver, higher micro stepping (1/32) 2.Increase 3.3/5V input signal switch, compatible with 3.3V microcontroller 3.Expand the driver Enable pins, support sleep mode SPECIFICATION Input Voltage: 8.2-45 VDC Output current: 1.6 A (Limited) Working voltage: 3.3/5 V Driving pin: D4, D5, D6, D7, D8, D12 Microstep resolutions: full, 1/2, 1/4, 1, 8, 1/16, 1/32 Support Dual Bipolar Stepper Motor Support XBee interface Compatible with the Arduino UNO R3, Leonardo, Mega microcontroller Dimension: 83 * 55 * 25 mm/3.26 * 2.16 * 0.98 inches Weight: 48 g SHIPPING LIST SDual Bipolar Stepper Motor Shield for Arduino (DRV8825) x1

  • Brand: DFROBOT
  • ASIN: B07B7P2YW3
  • UPC: 664248533654
  • Part No: DF-AK034
Controller Bipolar Motor Stepper - TB6600 4A 9-42V Stepper Motor Driver CNC Controller, Stepper Motor Driver Nema tb6600 Single Axes Two Phase Hybrid Stepper Motor for CNC
TB6600 4A 9-42V Stepper Motor Driver CNC Controller, Stepper Motor Driver Nema tb6600 Single Axes Two Phase Hybrid Stepper Motor for CNC

Product Advantages: The TB1H is a high performance microstepping driver based on the latest original for high-efficiency TB6600HG for IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Feature: PWM chopper type bipolar stepper motor driver IC. 1. 9V-42V DC power supply. 2. H bridge bipolar constant phase flow drive. 3. the maximum 4.0A of the eight kinds of output current. 4. the largest 32 subdivision of the 6 models are optional. 5. input signal high speed photoelectric isolation. 6. common-anodestandard single pulse interface. 7. offline to maintain the function. 8. semi closed enclosure can be adapted to a more stringent environment. 9. to provide energy-saving semi-automatic current lock function. 10. built-in temperature protection and over current protection. IC parameter: single chip bipolar sine microstep stepper motor driver. the new BiCD 0.13 nm process. up to 42V. resistance (a +) = 0.4. the forward and reverse rotation control. 5 subdivision mode options (1/1, 1/2, 1/4, 1/8, 1/16,1/32). output current: IOUT = 4.0A (peak, in 100ms). rated output: IOUT = 3.5 A. package: HZIP25 - 1.00F. input port internal pull-down resistor: 100 K. alarm output pin current:Ialert = 1mA. monitoring output pin (MO): Imo= 1m...

  • Brand: NUOXINUS
  • ASIN: B07B9ZQF5D
  • UPC: 713839364419
  • Part No: TB6600
Bipolar Controller Stepper Motor - Geckodrive G540 4-Axis Bipolar Stepper Motor Driver
Geckodrive G540 4-Axis Bipolar Stepper Motor Driver

The G540 is a complete 4-axis system which plugs directly into your computer via the parallel port and to your motors through DB9 connectors. It contains four of our G250 drives, our own breakout board and a hard anodized aluminum case. Specifications Current Version Four 10 microstep fixed resolution discrete motor controls 0 to 3.5A rated phase current 18VDC to 50VDC supply voltage Mid-band resonance damping Auto standby current (70% current) Short-circuit protected Optoisolation on all LPT signal pins Two 1A at 0 to 50VDC rated outputs Four SPST to GND inputs FAULT indicator LED,signal to PC POWER indicator LED I-SET resistor on motor connector Morphs to full step at higher speeds to maximize motor torque TRIM adjust for motor smoothness Panel mount (5.7" by2.4" hole dim.) Anodized aluminum package No heatsink needed below 40C ambient Easy to service, removable drives Modular PCB design with no internal wires 10kHz watchdog timer (charge pump) Optoisolated analog output for a VFD drive Conservative ratings, premium components Comes with four backshells and four DB9 solder cup connectors

  • Brand: Geckodrive
  • ASIN: B00O3GU2ZA
  • UPC: 852675066382
  • Part No: Gecko Driver G540 4 Axis Stepper Driver
Stepper Controller Motor Bipolar - 4 Pack TB6600 4A 9-42V Stepper Motor Driver CNC Controller, Stepper Motor Driver Nema tb6600 Single Axes Two Phase Hybrid Stepper Motor for CNC
4 Pack TB6600 4A 9-42V Stepper Motor Driver CNC Controller, Stepper Motor Driver Nema tb6600 Single Axes Two Phase Hybrid Stepper Motor for CNC

Product Advantages: The TB1H is a high performance microstepping driver based on the latest original for high-efficiency TB6600HG for IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Feature: PWM chopper type bipolar stepper motor driver IC. 1. 9V-42V DC power supply. 2. H bridge bipolar constant phase flow drive. 3. the maximum 4.0A of the eight kinds of output current. 4. the largest 32 subdivision of the 6 models are optional. 5. input signal high speed photoelectric isolation. 6. common-anodestandard single pulse interface. 7. offline to maintain the function. 8. semi closed enclosure can be adapted to a more stringent environment. 9. to provide energy-saving semi-automatic current lock function. 10. built-in temperature protection and over current protection. IC parameter: single chip bipolar sine microstep stepper motor driver. the new BiCD 0.13 nm process. up to 42V. resistance (a +) = 0.4. the forward and reverse rotation control. 5 subdivision mode options (1/1, 1/2, 1/4, 1/8, 1/16,1/32). output current: IOUT = 4.0A (peak, in 100ms). rated output: IOUT = 3.5 A. package: HZIP25 - 1.00F. input port internal pull-down resistor: 100 K. alarm output pin current:Ialert = 1mA. monitoring output pin (MO): Imo= 1m...

  • Brand: NUOXINUS
  • ASIN: B07HCZQ4P8
  • UPC: 687345903106
  • Part No: 0022-TB6600
Motor Bipolar Stepper Controller - Beauty Star Stepper Motor Driver, 3PCS TB6600 4A 9-42V Nema 17 Stepper Motor Driver CNC Controller Single Axes Hybrid Stepper Motor Controls
Beauty Star Stepper Motor Driver, 3PCS TB6600 4A 9-42V Nema 17 Stepper Motor Driver CNC Controller Single Axes Hybrid Stepper Motor Controls

Feature: PWM chopper type bipolar stepper motor driver IC 1. 9V-42V DC power supply 2. H bridge bipolar constant phase flow drive 3. the maximum 4.0A of the eight kinds of output current 4. the largest 32 subdivision of the 6 models are optional 5. input signal high speed photoelectric isolation 6. common-anodestandard single pulse interface 7. offline to maintain the function 8. semi closed enclosure can be adapted to a more stringent environment 9. to provide energy-saving semi-automatic current lock function 10. built-in temperature protection and over current protection. Can control 2 phase stepper motor forward and reverse rotation, With 1-2, W1 -2 , 2W1 -2, 4W1 -2 phase excitation mode. Only the clock pulse signal can be driven two-phase bipolar stepper motor to achieve low vibration, high efficiency work. IC parameter: single chip bipolar sine microstep stepper motor driver the new BiCD 0.13 nm process up to 42V resistance (a +) = 0.4 ?the forward and reverse rotation control 5 subdivision mode options (1/1, 1/2, 1/4, 1/8, 1/16,1/32) output current: IOUT = 4.0A (peak, in 100ms) rated output: IOUT = 3.5 A package: HZIP25 - 1.00F input port internal pull-down resistor: 100 K alarm output pin current:Ialert = 1mA monitoring output pin (MO): Imo= 1mA with reset and enable ...

  • Brand: Beauty Star
  • ASIN: B077MDVTF9
  • UPC: 661273114902
  • Part No: 202507-US1
 - Hilitand Stepper Motor Bipolar,Nema 17 Stepper Motor Bipolar 2.8A 2 Phase 4-wire 4-lead 3D Printer/CNC
Hilitand Stepper Motor Bipolar,Nema 17 Stepper Motor Bipolar 2.8A 2 Phase 4-wire 4-lead 3D Printer/CNC

Bipolar Stepper Motor Controller

 - Ejoyous Nema 17 Stepper Motor Bipolar 2.8A 2 Phase 4-wire 4-lead 3D Printer/CNC
Ejoyous Nema 17 Stepper Motor Bipolar 2.8A 2 Phase 4-wire 4-lead 3D Printer/CNC

Bipolar Stepper Motor Controller

 - Stepper Motor 17 Bipolar 16mm 0.315NM 1.5A 3.6V 4 Lead Cable for 3D Printer CNC Router Laser Lathe Machine Stage Light C
Stepper Motor 17 Bipolar 16mm 0.315NM 1.5A 3.6V 4 Lead Cable for 3D Printer CNC Router Laser Lathe Machine Stage Light C

Bipolar Stepper Motor Controller

  • Color: othersOther
  • Size: 16x5mm
 - Electric Stepper Motor - Rockshaft Control Valve, New, John Deere, AL78213
Electric Stepper Motor - Rockshaft Control Valve, New, John Deere, AL78213

Bipolar Stepper Motor Controller

 - 57oz-in 1Nm NEMA 17 Stepper Motor 1.3A 40mm DC12V 2-Phase 4000g.cm 4-Lead 1.8 Degree for CNC router or mill
57oz-in 1Nm NEMA 17 Stepper Motor 1.3A 40mm DC12V 2-Phase 4000g.cm 4-Lead 1.8 Degree for CNC router or mill

Bipolar Stepper Motor Controller

  • Color: Black
 - GM STEPPER MOTOR X25-168 X25.168 GAUGE SPEEDOMETER X27 168
GM STEPPER MOTOR X25-168 X25.168 GAUGE SPEEDOMETER X27 168

Bipolar Stepper Motor Controller

  • Color: White
  • Size: others
  • Rating: 4.5
 - 2pcs Universal White X27 589 Instrument Cluster Gauge Stepper Motor for Car
2pcs Universal White X27 589 Instrument Cluster Gauge Stepper Motor for Car

Bipolar Stepper Motor Controller

 - Nema 14 4  1.8 Degree CNC Stepping Stepper Motor 28mm 0.8A 17oz.in
Nema 14 4 1.8 Degree CNC Stepping Stepper Motor 28mm 0.8A 17oz.in

Bipolar Stepper Motor Controller

  • Color: othersOther
  • Size: others

Stepper Motors with Arduino - Controlling Bipolar & Unipolar stepper motors

Bipolar Stepper Motor Controller

Full Article with Code at https://dbot.ws/stepper More projects at https://dronebotworkshop.com Today we will be working with stepper motors, a versatile yet often misunderstood electromechanical component used in a variety of devices. After examining how stepper motors work and what the diffe...

Tags: Stepper Motor (Engine Category),stepper,motor,A...

Bipolar Stepper Motor Controller A3404 Search Results

Want more Bipolar Stepper Motor Controller similar ideas? Try to explore these searches: 12v Ac Mobile, Farm Pattern, and Paper Flower Stickers.

AllinShopy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or one of its affiliates.